The Electrical System | Beginner’s Auto Maintenance & Repair | Jeff Crawford

The Electrical System: This chapter is about the electrical system of the vehi-cle. The main parts of the electrical system are the battery, alternator, and ignition system. The battery is the power source of the whole vehi-cle. The alternator is a re-charging device that is used to maintain the charge of the battery. The ignition system is used to ignite the fuel at the correct time during the Otto cycle of events (review Chapter 5 for the Otto cycle of events).

 

The Electrical System | Beginner’s Auto Maintenance & Repair | Jeff Crawford

 

 

The Electrical System | Beginner's Auto Maintenance & Repair | Jeff Crawford

 

The “ignition” in this lesson is not the same as the key ignition; it’s about the ignition system that is used in the engine to ignite the air-fuel mixture in the combustion chamber. Prior to 1975, the ignition system consisted of the ignition coil, capacitor, contact breaker, distributor, and spark plugs. The ignition coil converts low voltage electricity into high voltage. The high voltage electricity is sent to the distributor through the rotor, then it transmits out the distributor cap through plug wires to the spark plugs. The contact breaker or contact points complete and interrupt the circuit to the ignition coil on the low voltage side. The capacitor absorbs a voltage spike when the points open to avoid burning the contacts of the points.

 

ln a modern vehi-cle the ignition system consists of a crankshaft position sensor, which sends a signal to the PCM (powertrain control module or computer). The PCM interprets the signal and sends a signal to the ignition coils on each cylinder. Then the ignition coils fire through the spark plugs. Some vehi-cles will use one coil for two cylinders, and some have a separate coil for each cylinder. When one coil is used for two cylinders, the spark plugs for both cylinders fire at the same time, but one of the cylinders will be in the exhaust step of the Otto cycle, so it’s kind of a waste spark (not used to ignite fuel).

 

The Electrical System | Beginner's Auto Maintenance & Repair | Jeff Crawford

 

The ignition system works in conjunction with fuel injection (Chapter 7) so that the correct Otto Cycle of events occurs in the cylinders. The cylinders of internal combustion engines are numbered and the firing sequence occurs in a specific order. The firing order can vary by vehi-cle make and model. The engine size is also a factor.

 

For example, in an 8-cylinder Chevy engine, the cylinders might be numbered 1, 3, 5, 7 on the driver’s side (or left side of the engine from the driver’s perspective), and 2, 4, 6, 8 on the passenger side. The firing order for this particular engine would be 1, 8, 4, 3, 6, 5, 7, 2.

 

The Electrical System | Beginner's Auto Maintenance & Repair | Jeff Crawford
illustration of numbered cylinders of a V8 engine; the driver’s side is the right side of this image since the front of the engine is towards the bottom of the image.

 

Spark Plug Gap:

 

The purpose of the spark plug gap is to create an electric arc or spark of high heat to ignite the air-fuel mixture in the combustion chamber at the correct time. lf the gap is too small then the spark is not hot enough to ignite the fuel. lf the gap is too wide, then the voltage is not high enough to create a spark. Either condition can create an ignition misfire, causing poor performance and high emissions.

 

How to Safely Jump Start a vehi-cle with a Failed Battery:

 

When a battery loses its charge the vehi-cle won’t start and it becomes necessary to use another vehi-cle for a jump start. Since jump starting a failed battery with a charged battery involves creating an electrical circuit, it is important to follow the right steps to perform a jump start safely:

  1. Do your best to line up the vehi-cles so that the two batteries are close enough to connect jumper
  2. Turn off the active vehi-cle
  3. Verify there is no odor (like sulfur) coming from either lf there is a sulfur odor do not attempt to jump start the vehi-cle. The battery could explode due to the gas that is released (hydrogen gas).
  4. The next steps involve connecting the When connecting cables to the first vehi-cle, which is the dead vehi-cle, make sure the other ends of the cables are not touching each other.
  5. First connect the red cable to the positive (red) battery terminal on the dead battery or to the jump start locations specified in the owner’s
  6. Connect the black cable to the negative terminal of the dead battery or to the jump start locations specified in the owner’s
  7. Connect the positive (red) cable to the positive terminal of the working vehi-cle (or to the specified jump start location in the owner’s manual of the working vehi-cle).
  8. Connect the negative (black) cable to the negative terminal of the working vehi-cle (or to the specified jump start location in the owner’s manual of the working vehi-cle) or to anything The metal must be bare or without any paint that would inhibit the conduction of electricity. The engine block is sufficient. Yet, the negative terminal is often the most accessible.
    1. (More briefly the order is: dead red, dead black, live red, then live Red is always positive, black is always negative.)
  9. Start the working vehi-cle and allow it to run for approximately 5
  10. Attempt to start the other lf the vehicle fails to start, there may be additional problems or the battery is no longer rechargeable.
  11. Take off the cables in reverse order (always remove negative first) and make sure the cables don’t touch each other as you’re removing them
    1. Remove the negative cable from the jumped vehicle
    2. Remove the positive cable from the jumped vehicle (make sure they don’t touch each other)
    3. Remove the negative cable from the previously working vehicle
    4. Remove the positive cable from the previously working

 

The Electrical System | Beginner's Auto Maintenance & Repair | Jeff Crawford

 

That may seem like a lot of steps above to memorize, so here are some tricks to remember the process: first connect the Dead Red, Fred. This phrase will help you remember that when connecting the cables you’ll start with the positive cable on the dead battery. The order is dead red, dead black, live red, live black. Then it’s the reverse order to remove the cables after the dead battery is jumped: First remove the Jumped Black, Jack. Remove the jumped black, jumped red, then the previously live black, then the previously live red.

 

Never attempt to jump-start a diesel vehicle. Since a diesel engine battery requires much more power, attempting to jump-start it could damage the running vehicle.

 

Typically you can attempt to jump-start a hybrid car, but if the high-power battery is dead, the vehicle will not start. However, a hybrid can be used to jump-start a regular gasoline vehicle.

Know more: 

 

Leave a Comment